| Customization: | Available |
|---|---|
| Type: | In-Mould Label |
| Material: | Epoxy |
|
Still deciding? Get samples of $ !
Order Sample
|
| Shipping Cost: | Contact the supplier about freight and estimated delivery time. |
|---|
| Payment Methods: |
|
|---|---|
| Support payments in USD |
| Secure payments: | Every payment you make on Made-in-China.com is protected by the platform. |
|---|
| Refund policy: | Claim a refund if your order doesn't ship, is missing, or arrives with product issues. |
|---|
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
| Item | 3d resin epoxy label sticker |
| Color | CMYK |
| Technology | Resin epoxy |
| Thickness | 25 microns |
| Package | Opp bag |
| Shipping | FedEx/ DHL / EMS ..... |
| Material | Epoxy PVC... |
| Design | AI/CDR/EPS/PDF/JPG,outlined draft or LOGO file. |
Crystal drop resin (dropping) labels, signs, and trademarks are made using imported epoxy resin to produce flat transparent soft and hard crystal resin products, and the coating and casting of various printed trademark surfaces, making exquisite dropped labels. It is a modern surface decoration material with bright transparent surface, bright colors, and easy to paste. The manual operation process of crystal drop resin labels, signs, and trademarks is as follows:
1. First prepare various base materials, such as: rod glue, PVC, laser material labels, synthetic paper, metal, aluminum sheet, stainless steel, plastic, copper plate paper acrylic, and place them in an oven for preheating at 60 degrees, the purpose is to remove the moisture from the surface.
2. After deidification, place the base material flat on the glass plate of the operation table with consistent horizontal level, waiting for dropping (dropping resin).
3. According to amount, take a clean beaker, accurately measure, and mix the components A and B in a weight ratio of 2:1, stir evenly (be sure mix evenly, otherwise there will be a phenomenon of surface stickiness and delamination from the base material, and this should be achieved for all products.)
4. Then the mixed material in a vacuum drying oven, turn on the vacuum pump, and remove the bubbles in the mixed material under vacuum.
5. Take a clean syringe suck the defoamed crystal resin into the syringe, then measure and evenly drop it on the surface of the pre-prepared base material (i.e., signs labels, trademarks, etc.), generally the thickness of the crystal resin layer is 2mm, and let it naturally flow flat.
6. After 3-5 minutes dropping the crystal resin on the base material, observe whether there are bubbles or dust particles on the surface of the glue, if there are small bubbles, you can burst with a large-headed pin, and if you find that there are places where the crystal resin has not flowed in the dead angle, you can use a large-headed pin guide it.
7. The signs made of crystal drop resin are cured and hardened at room temperature of 20°C-30°C for 10-4 hours, becoming a crystal sign that does not stick to the hand.
8. If you encounter self-adhesive labels, trademarks, etc., which are very thin have no obvious boundary, it is easy to cause the crystal resin to overflow during casting, and it is difficult to achieve a thickness of 2mm, so the of the crystal resin should be different according to different situations, and the viscosity should be well controlled. In the process of use, it can be placed for 12 hours to increase the viscosity and adapt to the casting of thin crystal resin.
9. To make crystal drop resin (dropping sign) signs thicker than 2, you can drop twice, after the first dropping, solidify for 3-5 hours, and then drop another layer.
10. Cleaning after dropping, manual dropping resin or automated dropping resin, the machine, equipment, and containers need to be cleaned up after completion, because the crystal resin hardens and does not dissolve any solvent, so it must be cleaned up before it hardens. (Suggestion: use acetone or anhydrous alcohol
){kind=link}